How to plot power and fan in artisan

[Mayowarlord]

I see some of you plot power and fan. How do I do that?

[SusanJoM]

One way is to set up buttons like these to represent the events you want to record.
There are some rudimentary directions in the Downloads Section
>Artisan and the Phidget and the HUKY
> #2 Configure the Events

[kctremel]

awesome. thanks for info!

[Mayowarlord]

One way is to set up buttons like these to represent the events you want to record.
There are some rudimentary directions in the Downloads Section
>Artisan and the Phidget and the HUKY
> #2 Configure the Events

Thanks Susan,
I added buttons, and the events are being marked on my ET/BT lines, I found the setting to make those events plot also, but they are not dynamic. It seems that the plot flat lines rather than going up and down to match the values I have assigned to them on the button page.

What I am really after here, is the best way to follow along while I am roasting to re create a profile that I liked. It seems like the best way has been pulling up the events page from the old profile and just writing down the temps I made changes at. I feel like I am using Artisan like a type writer

[SusanJoM]

My powers of visualization are sadly lacking.
Would you please post a profile so that I can understand better what you are describing?

And maybe you could post (or link to) a picture of a profile which is looking the way you want yours to look?

There are three different ways that the information you plug in using your buttons will show up on your graph.  There is a blank, there is "type" and there is "value".  Play  with those to see if that sorts you out.
Below are versions of the very same profile with each of the three options selected:

Meanwhile I'm gonna attach a Phidget to my HUKY2 (a solid drum/fast motor)....whoopeeeeeee....

[Mayowarlord]

My powers of visualization are sadly lacking.
Would you please post a profile so that I can understand better what you are describing?

And maybe you could post (or link to) a picture of a profile which is looking the way you want yours to look?

There are three different ways that the information you plug in using your buttons will show up on your graph.  There is a blank, there is "type" and there is "value".  Play  with those to see if that sorts you out.
Below are versions of the very same profile with each of the three options selected:

Meanwhile I'm gonna attach a Phidget to my HUKY2 (a solid drum/fast motor)....whoopeeeeeee....

Thanks for all your help Susan. I am at work and away from my computer with Artisan, but I will post images later.

I have what you showed in image 2, but would really prefer image three. I bet I can sort it out.

What would be really awesome is if the time and temp of the event pupped up when you hovered over it.

[Mayowarlord]

My powers of visualization are sadly lacking.
Would you please post a profile so that I can understand better what you are describing?

And maybe you could post (or link to) a picture of a profile which is looking the way you want yours to look?

There are three different ways that the information you plug in using your buttons will show up on your graph.  There is a blank, there is "type" and there is "value".  Play  with those to see if that sorts you out.
Below are versions of the very same profile with each of the three options selected:

Meanwhile I'm gonna attach a Phidget to my HUKY2 (a solid drum/fast motor)....whoopeeeeeee....

Thanks for all your help Susan. I am at work and away from my computer with Artisan, but I will post images later.

I have what you showed in image 2, but would really prefer image three. I bet I can sort it out.

What would be really awesome is if the time and temp of the event pupped up when you hovered over it.

My issue is resolved. I had events set to +- rather than just power, fan etc. Switching it changed my profiles to immediately look like example 2. 

Cheers!

[trumz]

I have a quick question regarding ploting power and fan. 

I have custom event bottons set for my power, such as gas 1.5 kPa = event value 15, gas 2.2 kPa = even value 22.  But they only display as "P1" if I select anything between 1.0 and 1.9.  I can't get, for example, P15 to show when I click my gas 1.5 kPa bottton.

Susan, I can see in your first picture that you're able to get specific numbers on those gas setting, how did you do that?

[SusanJoM]

You are construing event value differently than I have.

Since my maximum gas (as delimited by the gauge I am using) is 3.75 kPa, so my value for 3.75 is 100%.
the value for 3.0 kPa would be 3/3.75 = 80%.  2.5 kPa would be 2.5/3.75 = 66% etc.

[trumz]

Do you have those numbers (100, 80, 66) put into Event Value?  If you chose 83 for example, does it show 83 or 80?

Even though I have it set up differently then you, I should be able to display on the graph the correct Value I chose in the menu.

[SusanJoM]

Here's a snapshot of the Events >Bottons page

[trumz]

Hi Susan, thanks for that.  My Values are set similarly, but if I hit my 1.4 kpa button, which has a Value of 14, it will show on the graph as "P1", not "P14".  Similarly, for example my 2.2 kpa button with Value of 22 shows on graph as "P2".

Makes it hard to go back to a graph and see what power settings I used.  Any idea?

[SusanJoM]

I understand your predicament, but I think that the translation of P1, P2, P3  to a particular kPa may be your responsibility.

If there is a way to change that it would be good to know and I suggest that you inquire at the Artisan user list to see if anyone knows how to do it.  And let us know if you find out.

[LTB]

remember that you can put a curve in the background, with or without the event, to follow it !

[hankua]

Hi Susan, thanks for that.  My Values are set similarly, but if I hit my 1.4 kpa button, which has a Value of 14, it will show on the graph as "P1", not "P14".  Similarly, for example my 2.2 kpa button with Value of 22 shows on graph as "P2".

Makes it hard to go back to a graph and see what power settings I used.  Any idea?

Take a look at the download section; Susan has instructions how to include percentages inside the buttons that will display.